| 会员中心 |
www.164580.com/member/ |
|
| 繁體中文 |
big5.164580.com/ |
|
| 产品与标准 |
www.164580.com/biaozhun/ |
|
| 繁体 |
https://big5.164580.com/info_412794.html |
|
| 最小破坏扭矩 |
www.164580.com/data/detail_241.html |
|
| ASME B 18.6.3H5B-I/H5C-IA+T1A - 2024 |
www.164580.com/info_425510.html |
|
| ASME B 18.6.3 (T18-I/T19-IA+T40) - 2013 |
www.164580.com/info_412794.html |
|
| ASME B 18.6.3 (T20-I+T40) - 2013 |
www.164580.com/info_412845.html |
|
| ASME B 18.6.3 (T20-IA+T40) - 2013 |
www.164580.com/info_412862.html |
|
| ASME B 18.6.3 (T20-III+T40) - 2013 |
www.164580.com/info_412879.html |
|
| 自攻螺钉拧入性试验用标准试验板厚度和孔径 [Table 48] |
www.164580.com/info_85340.html |
|
| TRS型自挤自攻螺钉的最大扭矩 [Table 49] |
www.164580.com/info_85357.html |
|
| 自攻螺钉的抗扭强度 [Table 50] |
www.164580.com/info_85374.html |
|
| 机械螺钉和自攻螺钉的通用要求 |
www.164580.com/info_413066.html |
|
| 产品表单总览 |
www.164580.com/info_413185.html |
|
| 开槽盘头螺钉 [Table 17] (ASTM F837, F468) |
www.164580.com/info_84796.html |
|
| 开槽盘头 AB ABR自攻螺钉 |
www.164580.com/info_412777.html |
|
| 十字槽盘头螺钉 [Table 18] (ASTM F837, F468) |
www.164580.com/info_84813.html |
|
| 四方槽盘头螺钉 [Table 19] (ASTM F837, F468) |
www.164580.com/info_86717.html |
|
| 四方槽盘头 AB ABR自攻螺钉 |
www.164580.com/info_412811.html |
|
| 梅花槽盘头螺钉 |
www.164580.com/info_412199.html |
|
| 梅花槽盘头 AB ABR自攻螺钉 |
www.164580.com/info_412828.html |
|
| 普通螺纹收尾、肩距、退刀槽和倒角 (ISO 3508:1976 / ISO 4755:1983) |
www.164580.com/info_369512.html |
|
| 紧固件机械性能 不锈钢和镍合金紧固件选用指南 |
www.164580.com/info_366129.html |
|
| 普通螺纹 公差 |
www.164580.com/info_411264.html |
|
| 普通螺纹搓制和滚制前的毛坯直径 |
www.164580.com/info_82365.html |
|
| 统一螺纹搓制和滚制前的毛坯直径 |
www.164580.com/info_392700.html |
|
| 紧固件 - 螺栓、螺钉和螺柱 - 公称长度和螺纹长度 (ISO 888:2012, MOD) |
www.164580.com/info_369444.html |
|
| 普通螺纹（一般用途米制螺纹）- 直径与螺距系列 (ISO 261: 1998, MOD) |
www.164580.com/info_367846.html |
|
| 紧固件公差（螺栓、螺柱、螺钉和螺母） |
www.164580.com/info_73287.html |
|
| 普通螺栓和螺钉 - 头下圆角半径 |
www.164580.com/info_380358.html |
|
| 镀锌、镀镍、镀镉、复合镀等层镀层盐雾腐蚀的防护性能 |
www.164580.com/info_80257.html |
|
| 紧固件表面缺陷 - 螺栓、螺钉和螺柱 - 一般要求 |
www.164580.com/info_371314.html |
|
| 紧固件表面缺陷 - 螺栓、螺钉和螺柱 - 特殊要求 |
www.164580.com/info_371433.html |
|
| 黑色金属硬度及强度换算值 |
www.164580.com/info_357986.html |
|
| 沉头螺钉 第2部分 十字槽插入深度 |
www.164580.com/info_409462.html |
|
| Chinese Source Page |
https://www.164580.com/info_412794.html |
|
| © 易紧通 |
www.164580.com |
|
正在请求数据,请稍候...