| 会员中心 |
www.164580.com/member/ |
|
| 繁體中文 |
big5.164580.com/ |
|
| 产品与标准 |
www.164580.com/biaozhun/ |
|
| 简体 |
https://www.164580.com/info_369155.html |
|
| 繁体 |
https://big5.164580.com/info_369155.html |
|
| 米/英制螺纹对照 |
www.164580.com/data/detail_7.html |
|
| 螺纹直径与受力截面积 |
www.164580.com/data/detail_238.html |
|
| 最小破坏扭矩 |
www.164580.com/data/detail_241.html |
|
| GB /T 13807.2SD |
www.164580.com/biaozhun/?srd=2151 |
|
| DIN 2510-3KU |
www.164580.com/biaozhun/?srd=2155 |
|
| DIN 2510-3 (L) - 1971 |
www.164580.com/info_369070.html |
|
| DIN 2510-3 (K) - 1971 |
www.164580.com/info_369104.html |
|
| DIN 2510-3 (KU) - 1971 |
www.164580.com/info_369155.html |
|
| DIN 2510-3 (Z) - 1971 |
www.164580.com/info_369172.html |
|
| DIN 2510-3 (ZU) - 1971 |
www.164580.com/info_369189.html |
|
| 60° 中心孔 - R 型, A 型, B 型 与 C 型 |
www.164580.com/info_369036.html |
|
| 带缩径杆的螺栓连接件 带大间隙的米制螺纹 标称尺寸和极限尺寸 |
www.164580.com/info_421039.html |
|
| 普通螺纹收尾、肩距、退刀槽和倒角 (ISO 3508:1976 / ISO 4755:1983) |
www.164580.com/info_369512.html |
|
| 紧固件机械性能 不锈钢和镍合金紧固件选用指南 |
www.164580.com/info_366129.html |
|
| 普通螺纹 公差 |
www.164580.com/info_411264.html |
|
| 普通螺纹搓制和滚制前的毛坯直径 |
www.164580.com/info_82365.html |
|
| 统一螺纹搓制和滚制前的毛坯直径 |
www.164580.com/info_392700.html |
|
| 紧固件 - 螺栓、螺钉和螺柱 - 公称长度和螺纹长度 (ISO 888:2012, MOD) |
www.164580.com/info_369444.html |
|
| 普通螺纹（一般用途米制螺纹）- 直径与螺距系列 (ISO 261: 1998, MOD) |
www.164580.com/info_367846.html |
|
| 紧固件公差（螺栓、螺柱、螺钉和螺母） |
www.164580.com/info_73287.html |
|
| 镀锌、镀镍、镀镉、复合镀等层镀层盐雾腐蚀的防护性能 |
www.164580.com/info_80257.html |
|
| 紧固件表面缺陷 - 螺栓、螺钉和螺柱 - 一般要求 |
www.164580.com/info_371314.html |
|
| 紧固件表面缺陷 - 螺栓、螺钉和螺柱 - 特殊要求 |
www.164580.com/info_371433.html |
|
| 黑色金属硬度及强度换算值 |
www.164580.com/info_357986.html |
|
| © 易紧通 |
www.164580.com |
|
正在请求数据,请稍候...